Skip to content

Arm® Cortex®-M0+ processor-based microcontroller

minIC™

Engineered by HEX Microchip.

minIC is a general-purpose 32-bit microcontroller built around an Arm Cortex-M0+ processor, combining a broad mixed-signal peripheral set with an application held in external SPI NOR flash and run from SRAM — developed by HEX Microchip for appliance, industrial and building-control applications.

  • 192 KB SRAM
  • 80 MHz †
  • 12-bit ADC
  • Single 3.3 V supply

† Target value, pending silicon characterization.

minIC — an Arm Cortex-M0+ processor-based microcontroller, shown above its socket

Visuals are for illustrative purposes only.

Why minIC

A real semiconductor product.

  • 01

    A complete microcontroller

    An Arm Cortex-M0+ processor with 192 KB of SRAM, a boot ROM and an external SPI NOR flash interface, integrated communication, timing and control peripherals, mixed-signal analog blocks, clocking and power management — on a single device.

  • 02

    A broad mixed-signal peripheral set

    CAN 2.0A/B, LIN 2.x, quad-lane xSPI, a 12-bit SAR ADC and a hardware PID accelerator alongside four PWM channels — running from a single 3.3 V supply.

  • 03

    Accessible engineering and product support

    Direct access to the engineering team, evaluation support, and the possibility of closer technical cooperation with OEMs and product developers.

Visuals are for illustrative purposes only.

Beneath the package: an Arm Cortex-M0+ processor, integrated into silicon developed by HEX Microchip.

Visuals are for illustrative purposes only.

Architecture

An Arm Cortex-M0+ processor, integrated into silicon developed by HEX Microchip.

minIC is built around the Arm Cortex-M0+ processor — a widely adopted, well-supported core for embedded control — with 192 KB of on-chip SRAM, a 16 KB boot ROM and an external SPI NOR flash interface on a single-master AHB-Lite bus, surrounded by an integrated set of communication, timing, control and analog blocks with their own clocking, reset and power management.

Arm Cortex-M0+, Armv6-M
Little-endian, with a 32-line NVIC across four priority levels and a single-master AHB-Lite interconnect.
Application in SPI NOR flash, executed from SRAM
One external SPI NOR flash of up to 16 MB, on dedicated pads, holds the application image, parameters and data. At boot the application is copied into the 192 KB of on-chip SRAM and executed from there; execute-in-place from the flash window is also supported.
Integrated mixed-signal peripherals
CAN 2.0A/B, LIN 2.x and IrDA-capable UARTs, I²C, SSP/SPI and a quad-lane xSPI master, alongside four 32-bit timers, four PWM channels, a PID accelerator, a 12-bit SAR ADC, a 17-bit signed ΔΣ DAC and an analog comparator.
Clock, reset and power architecture
A PLL with automatic frequency calibration, tunable high- and low-speed RC oscillators and an external reference feed a five-source glitch-free system clock multiplexer. The device runs from a single 3.3 V supply, with an on-chip LDO, power-on reset and brown-out detection.

Visuals are for illustrative purposes only.

Exploded view of the minIC package: lid, silicon die with its labelled functional blocks, substrate and interface pins.

Technical information

Quick specifications.

Selected parameters from the minIC Product Brief, Rev 1.2. Complete register maps, memory map and electrical characteristics are published in the datasheet.

Core & system

Processor
Arm Cortex-M0+
Architecture
Armv6-M, little-endian
Max system clock
80 MHz †
Interrupt controller
NVIC, 32 lines
System bus
AHB-Lite

Memory

SRAM
192 KB
Boot ROM
16 KB
SPI NOR flash
Up to 16 MB
Flash interface
Single-lane read/write access with dedicated pads

Clocks & reset

PLL / VCO
80 MHz †
HSI oscillator
4 – 12 MHz, tunable †
LSI oscillator
30 kHz †
External reference
2 – 48 MHz
System clock sources
5, glitch-free
Clock monitor
Internal clock period monitor

Communication

UART with LIN / IrDA
2, ≤ 10 Mbaud †
UART, basic
1, ≤ 5 Mbaud †
I²C master
3, 100 / 400 kHz
SSP / SPI
2
xSPI master (SPI / DSPI / QSPI)
1, ≤ 40 MHz †
CAN 2.0A/B
1, 25 kbit/s – 1 Mbit/s
LIN frame-ID table
16 entries

Timers & control

32-bit timer counters
4
PWM channels
4
PID accelerator
1
Real-time clock
1, with two alarms
SysTick timer
24-bit

Analog

ADC resolution
12-bit SAR
ADC channels
8 external + 7 internal
ADC input range
Rail-to-rail
DAC resolution
17-bit signed
DAC code range
±65535, midscale
DAC update rate
≤ 100 kSa/s
Analog comparator
1, with interrupt
Temperature sensor
Via ADC channel

Power

I/O supply (VDDIO)
3.3 V (3.0 – 3.6 V)
Core supply
On-chip LDO
Voltage reference
Integrated Bandgap, 1.2 V
Power-on reset
Integrated
Brown-out detect
4 levels, interrupt
Reset sources
External / POR / SW

I/O & debug

GPIO pins
32
GPIO interrupts
Per-pin, level / edge
Debug interface
JTAG
Package options
QFN64 / 80 / 88 / 100 — final package TBD

† Target values, pending silicon characterization. Interface rates scale with the system clock.

Preliminary specifications — minIC is under active development and all figures are subject to change without notice. The final package is not yet defined, and detailed ADC and comparator characteristics are pending characterization.

Visuals are for illustrative purposes only.

Applications

Where minIC fits.

Target application areas from the minIC Product Brief.

  1. 01Appliances
  2. 02Industrial
  3. 03Automotive
  4. 04Building & HVAC
  5. 05Energy & metering
  6. 06Motor & drives

01

Appliances

Washers, dishwashers, ovens and small domestic appliances — motor, heater and panel control with voice prompts.

02

Industrial

Factory automation, PLC I/O modules, sensor and actuator interfaces, closed-loop process control.

03

Automotive

Body electronics, LIN sub-networks, LIN/CAN gateways, comfort, lighting and mirror control.

04

Building & HVAC

Thermostats and zone controllers, valve and damper actuators, air handling, environmental sensing.

05

Energy & metering

Battery management, current sensing, power conversion control, sub-metering and monitoring.

06

Motor & drives

Brushed DC and stepper drive, pumps, fans and compressors, speed and position loops.

Visuals are for illustrative purposes only.

Target application areas are indicative. minIC is not qualified or certified for automotive, functional-safety or other regulated applications; automotive areas are listed as target applications only.

Who it is for

Built for teams building products.

  • Electronics manufacturers
  • OEMs
  • Embedded-system developers
  • IoT product companies
  • Industrial electronics companies
  • System integrators
  • Technology and R&D companies
  • Defence electronics companies
  • Universities and research organisations

Roadmap

From design to commercial availability.

Where minIC stands today. Specific sample, validation and production dates are shared directly with evaluation partners.

  1. 01

    Design & Verification

    Status: Complete

  2. 02

    Tapeout

    Status: In Progress

  3. 03

    First Silicon

  4. 04

    Validation

  5. 05

    Evaluation

  6. 06

    Commercial Availability

Tapeout

Final design sign-off and handoff for manufacturing. Photomasks are generated and the design enters fabrication.

In Progress

The current programme stage is confirmed directly with evaluation partners.

Pre-order

Pre-order minIC.

Register your interest in minIC. Tell us what you are building and we will come back to you with evaluation options and next steps. Pre-orders are registrations of interest — no payment is taken and no delivery date is implied.

An evaluation platform is part of the minIC productisation strategy. Kit contents and availability will be confirmed as the programme opens.

Documentation

Technical documentation.

The Product Brief is available now. Remaining documents follow as minIC enters the evaluation phase.

Preliminary documentation — subject to change without notice.

Company

A fabless semiconductor design company.

HEX Microchip is a fabless semiconductor company focused on the design and development of custom SoCs, ASICs and microcontrollers. The company provides expertise across digital and mixed-signal IC design, physical design and semiconductor product development, while developing its own semiconductor products including minIC.

Custom SoC, ASIC & MCU development
Custom semiconductor solutions spanning digital and mixed-signal domains.
Physical design
Implementation expertise carried through to manufacturable silicon.
Own product development
HEX develops its own semiconductor products and platforms, beginning with minIC.

Careers

Build what comes next.

Join HEX Microchip and work on semiconductor technologies spanning custom SoCs, ASICs, microcontrollers and advanced IC design.

An open application. We do not publish individual vacancies here — tell us where your work fits and we will come back to you.

PDF, DOC or DOCX. Maximum 5 MB.

Online applications will be available shortly.

Contact

Talk to our engineering team.

For product enquiries, evaluation requests and technical cooperation.